Tag Archives: Plumbers

Combining The Food Disposal With Your Dishwasher

It is not a difficult job to fit a garbage disposal unit in kitchen sink. There is no doubt that assembling its parts and checking it for no leaks is a time consuming exercise. And if we have a dishwasher, it will enhance the labor and time taken because dishwasher is emptied into the waste pipe. But with the fitting of the garbage disposal unit, the dishwasher is emptied in the garbage disposal.

These are easily connected to dishwasher drain lines so that the waste food drains into the disposal as well. Here is the stepwise procedure to attach the garbage disposal with the dishwasher.

To begin this process we shall first of all clean the bottom of the sink cabinet and keep a bucket beneath the sink. Using a pipe wrench, loosen the pipe and remove it. Any water in the pipe may be disposed in the bucket. Remove the drain pipe by unscrewing the long screws that joins the sink and the drain pipe.

Use a small putty knife to trim away the old plumber’s putty that helped seal the drain inside the sink, and lift the drain pipe out of the sink.

We shall connect the garbage disposal unit to the sink. Apply a coat of plumber’s putty of about quarter an inch around the sink hole and place the sink mounting assembly and the flange piece through the hole and fit it into the cabinet underneath. The drain pipe should be pressed on to the putty so that it can give a sealing effect. The ring is to be tightened by hand so that it does not move from its position on the sink. Wipe out any excess putty pushed out by the tightening.

Align the disposer with the three mounting ears on the sink mounting assembly. Holding the disposer in place, turn the lower mounting ring until all three mounting ears are locked into the mounting assembly.

Bringing the mounting and the disposal in line, slightly turn the unit and it will tighten and get locked with a click sound. The wall drain pipe can then be connected with the unit and using the J-trap supplied by the manufacturer.

The disposal plug should then be pushed into the outlet below the sink and the reset button be pressed. This will set the disposal ready for use. Open the water tap of the sink and look for leaks. Make sure the power is switched on and the disposal is activated. Also, ensure that the unit turns in. The water should keep running during the is process otherwise the unit may damage.

Scott Rodgers is a fine writer who has been providing great guidance on plumbing works all over USA. His exemplary knowledge has, in fact, sparked significant rise in revenue for talented plumbers across the nation, from Lawrenceville Plumbers (Need one?click here!) to Belleair Beach Plumbers (Need one?click here!).

Mending The Sprinkler Pipe Easily

A broken sprinkler pipe can be a major headache. Not only because it turns your garden into swampy land, but also because broken has pipe wasted a lot of precious water. Moreover, a leaky pipe may damage the nearby foundations as well.

Fortunately, fixing the problem isn’t too hard if you don’t mind getting dirty. Buy supplies. Nothing is worse than having to run to the hardware store in the middle of a project. See the list of things you need below. PVC pipe, PVC sleeve connectors, PVC pipe cutters or hack saw, PVC glue, PVC primer and safety glasses.

Turn off the water supply that leads to where the leak has been located. The water supply could be a main valve or it could be the valve leading from your hose. It is always advisable to wear the safety glasses to carry out such projects.

Dig around the area where you believe the broken pipe is. This is usually the area where water is bubbling up. Next take a hack saw and saw a straight edge on either side of the cracked PVC pipe. Remove the broken pipe. Sand the ends with sandpaper to get rid of the rough edge, this also helps to keep the area clean and ready for priming/gluing.

First, cut away enough pipe length so that the coupler, new section of pipe and slip-fix (fully compressed) can all fit. First fit the pipe without any glue to have the idea whether the pipe is nicely fitted or not.

If everything looks good, take the new pipe section apart and coat all pipe ends and the inside of the connectors with PVC primer. Let dry completely.

From here, you will want to put some glue on one end of the PVC sprinkler pipe. One great way to go about this is using popular blue glue, fitting the couplers onto the pipe during the twenty seconds that you have to do this.

Allow the glue to dry according to the directions on the package. Once the new section is completely dry, turn on the water and check for leaks.

Scott Rodgers is an author with ample plumbing experience all over the country. His exemplary guidance has created business for a lot of Fox Lake Plumbers (Need one?click here!) and Glenview Plumbers (Need one?click here!).