Tag Archives: Plumbers

Gardening

Stepwise Procedure To Inspect The Anti-Siphon Valve

Leave a comment

An anti-siphon valve is a device that prevents liquid from returning to the line from which it came if a siphon action occurs. An anti-siphon device is frequently required on outdoor irrigation systems to prevent possibly contaminated water to be drawn back into the water supply lines if water pressure decreases in the water supply line.

The anti-siphon valve is located on the outlet of the pump. This strategic location works against gravity and prevents draining on the tank. The valve opens when pressure is applied from the pump and then closes airtight at the moment the pump pressure ceases to flow. The anti-siphoning valve will close more tightly when negative drainage occurs.

Not only does the anti-siphon valve prevent someone from stealing gas, but it completely shuts out any unwanted contaminants with vacuum-tight sealing (made of thermoplastic) around the tank. The seal is a non-wet u-cup. This isolates the control spring. You will want to check from time to time to make sure your anti-siphon valve is operating properly; you can do this yourself without hiring a plumber.

All you need is to gather the tools needed while performing the task. Checking an anti- siphon valve would require tools like plumber’s wrench, shovel, and Teflon pipe tape.

Running the lawn sprinklers so as to fill them with water is the foremost steps in this respect. Now, turn off them after they are properly filled.

Curb the water to the main supply line that is going in the house. Bring out the piping from the ground by digging it accordingly. Disassociate the pipe from the anti- siphon valve. Make use of a plumber’s wrench to unscrew it.

Take off the sprinkler head; also keep an eye on the water flow that comes out of the pipe as you open this. Finding the flow of water from the pipe signifies the failure of the anti- siphon valve and you may need to replace it with a new one. If no water is coming out, your valve is working absolutely fine.

Wrap Teflon pipe tape two to three times around the threads of the pipe you opened and reattach the pipe by turning it clockwise with your plumber’s wrench.

Scott Rodgers is a fine expert who has been authoring on plumbing for a long time now. His talent has given inspiration to a host of workers, ranging from Buffalo Grove Plumbers (Need one?click here!) to Fort Sheridan Plumbers (Need one?click here!).

Gardening

Guide To Unclog A Blocked Drain

Leave a comment

Blocked drains are very inconvenient to handle but usually they remain a part of modern day plumbing. There are a few ways you can attempt to clear a blocked drain yourself without calling a professional plumber and soon have water running freely through the pipes again.

It is very important to know the cause of blockage to clean it out. Normally, blocking in a bathroom drain occurs due to trapping of hairs and soap scum in the drain. To remove it, you can use a wire, a screwdriver or another long and thin tool. The clearing of blocked drain should be done by pulling out the mass bit wise.

A plunger is also a good resort for clearing blocked drains. Cover the drain with the plunger, making sure that there is enough water in the sink or bathtub to cover the plunger cup.

Coating the rim of the plunger cup with petroleum jelly can help create a tighter seal for more suction. Press the plunger cup over the drain and pump the plunger 15 to 20 strokes. In many cases this will clear parts of the blockage and water may begin to flow.

A drain auger can also be used for clearing the drains. You can obtain a drain auger from any hardware and home supply store. Initially remove the filter or any stoppage attached to sink or tub drain and then put the drain auger down into the pipes. Carefully use the auger in the bends of the pipe. The auger would pull out or loose up the blockage causing impurities.

If the blockage is quite deep inside where auger could not reach easily then you would need to remove the sink trap. The draining water can be collected in a bucket. Now when you will use the auger at the opening of the sink trap, it may reach further.

Once the blocked drain is clear, run scalding hot water through the pipes for around ten minutes to remove as much residue as possible and reduce the chances of the blockage reoccurring again in the following weeks.

Hence, it must be clear by now that unblocking a blocked drain is not very difficult. It just needs some patience and determination. By solving the problem by your own, you can save a lot of money that would have been paid to a plumber otherwise.

Scott Rodgers is a noted author who has been providing ample guidance on plumbing works all across the nation. His luxurious knowledge has, in fact, sparked significant rise in revenue for talented plumbers across the nation, from Clifton Heights Plumbers (Need one?click here!) to Devon Plumbers (Need one?click here!).

Related Blogs